986 BSR # 17

Take a look at our trick little exhaust tips with aluminum exit bezel ! This dyno test shows the difference between our straight pipe extractor system and our dual high flow muffler package. The mufflers actually make more horse power & overall torque !  The test can also be seen & heard on YouTube, here are the links below. First test is with a straight pipe system that features a rear crossover, then with our high flow stainless steel dual muffler system.  Let us know what you think.  

http://www.youtube.com/watch?v=A63T_oIINIk                       

http://www.youtube.com/watch?v=rdZB7TPPvGQ                            


* The dyno results are based on the 986 BSR # 17 car with straight pipes, and then the #17 with our s.s. muffler system on the same car.


This exhaust system is available though PATRICK MOTORSPORTS !


We raced to an overall win at the HSR West 1 hour Enduro this October 2009 in our # 17 PORSCHE BSR / Boxster Spec. race car ! Here is the 996 GT-3 control arm, this shows the split design that allows the adjustment for added negative chamber to the car front & rear.  These are a must for proper set up, and to take full advantage of your TOYO 888 tires ! Here is our PATRICK MOTORSPORTS 986 996  997  under drive crank shaft pulley, this helps slow down the power steering (no more over heating), and is shown without the A/C and air pump to eliminate un needed drag. This helps the engine rev. quicker and make it more responsive !  Computer spin balancing the lightweight clutch package on our CWT 5000 balancing system !

We balance to within 0.1 oz. per inch from the center line of the crankshaft ! 

It does not get any better than that !

Let us know if we can help you with your balancing needs.
Receive an email notification when this project gallery is updated.

See The 57 Parts We Use ▶

This is one of our 986 BSR race cars. The #17 driven by James Patrick took 2) SPBOX class wins in the PCA sprint races at the California Festival of Speed in April 2009.

The more impressive win was the coveted “Workers Choice Award” for the entire PCA
Club race weekend ! Very unexpected, but a true honor !

Take a look, and let us know if we can help with your 986 BSR set up needs.

Take a look at our trick little exhaust tips with aluminum exit bezel !

Take a look at our trick little exhaust tips with aluminum exit bezel !

This dyno test shows the difference between our straight pipe extractor system and our dual high flow muffler package. The mufflers actually make more horse power & overall torque !  The test can also be seen & heard on YouTube, here are the links below. First test is with a straight pipe system that features a rear crossover, then with our high flow stainless steel dual muffler system.  Let us know what you think.  

http://www.youtube.com/watch?v=A63T_oIINIk                       

http://www.youtube.com/watch?v=rdZB7TPPvGQ                            


* The dyno results are based on the 986 BSR # 17 car with straight pipes, and then the #17 with our s.s. muffler system on the same car.


This exhaust system is available though PATRICK MOTORSPORTS !

This dyno test shows the difference between our straight pipe extractor system and our dual high flow muffler package. The mufflers actually make more horse power & overall torque ! The test can also be seen & heard on YouTube, here are the links below. First test is with a straight pipe system that features a rear crossover, then with our high flow stainless steel dual muffler system. Let us know what you think.

http://www.youtube.com/watch?v=A63T_oIINIk

http://www.youtube.com/watch?v=rdZB7TPPvGQ


* The dyno results are based on the 986 BSR # 17 car with straight pipes, and then the #17 with our s.s. muffler system on the same car.


This exhaust system is available though PATRICK MOTORSPORTS !


We raced to an overall win at the HSR West 1 hour Enduro this October 2009 in our # 17 PORSCHE BSR / Boxster Spec. race car !

We raced to an overall win at the HSR West 1 hour Enduro this October 2009 in our # 17 PORSCHE BSR / Boxster Spec. race car !

Here is the 996 GT-3 control arm, this shows the split design that allows the adjustment for added negative chamber to the car front & rear.  These are a must for proper set up, and to take full advantage of your TOYO 888 tires !

Here is the 996 GT-3 control arm, this shows the split design that allows the adjustment for added negative chamber to the car front & rear. These are a must for proper set up, and to take full advantage of your TOYO 888 tires !

Here is our PATRICK MOTORSPORTS 986 996  997  under drive crank shaft pulley, this helps slow down the power steering (no more over heating), and is shown without the A/C and air pump to eliminate un needed drag. This helps the engine rev. quicker and make it more responsive !

Here is our PATRICK MOTORSPORTS 986 996 997 under drive crank shaft pulley, this helps slow down the power steering (no more over heating), and is shown without the A/C and air pump to eliminate un needed drag. This helps the engine rev. quicker and make it more responsive !

Computer spin balancing the lightweight clutch package on our CWT 5000 balancing system !

We balance to within 0.1 oz. per inch from the center line of the crankshaft ! 

It does not get any better than that !

Let us know if we can help you with your balancing needs.

Computer spin balancing the lightweight clutch package on our CWT 5000 balancing system !

We balance to within 0.1 oz. per inch from the center line of the crankshaft !

It does not get any better than that !

Let us know if we can help you with your balancing needs.

986 BSR # 17 Parts

 Cool Shirt Cool Water Shirts in Blue
COOL SHIRT - COOL WATER SHIRT - BLUE - *HANS DEVICE COMPATIBLE - AVAILABLE IN SMALL, MEDIUM, LARGE, X-LARGE AND XX-LARGE *PLEASE SPECIFY SIZE WHEN ORDERING
Cool Shirt
 Cool Shirt Club System 24 Quart
COOL SHIRT - CLUB SYSTEM COMPLETE - 24 QUART -SEPARATELY

The Club 24 System comes with a 24qt cooling unit with an internal pump which supplies cooled water to the shirt through 8ft of double insulated hose with automatic shutoff / quick disconnects. The optional Temperature Control Switch gives the driver complete control of their comfort while in their race car. Total weight for the Club System is only 4lbs. Available options include the Temperature Control Switch, SFI-approved FireWear® fire-retardant Cool Shirt®, Universal Drain Kit, Emergency Pull-Release Connectors and Mounting Tray with strap.

The Club Systems are the most popular driver system manufactured. The Club System 24 combines the advantage of Cool Shirt®’s temperature-controlled cooling power with hours of cooling time.

Ideal for those racing applications where space is not as much of an issue and the races may run long. Versatile enough to be perfect for everything from road courses to oval track racing, the Club 24 System keeps you cool and alert for the entire race when going the distance really counts.

** COOL SHIRT SOLD SEPARATELY
Cool Shirt

Cool Shirt Club System 24 Quart ▶

PART # ACC CS CS-H-24 COOL SH
$298.00
 Cool Shirt - Temp Control Switch Kit
COOL SHIRT - TEMPERATURE CONTROL SWITCH - FLOW CONTROLLER
Cool Shirt
 Cool Shirt Firewear Cool Water Shirt - Large Short Sleeve
COOL SHIRT - FIREWEAR COOL WATER SHIRT - LARGE - SHORT SLEEVE *HANS DEVICE COMPATIBLE
Cool Shirt
 Cool Shirt Mounting Tray Kit for 24 Quart System
COOL SHIRT - MOUNTING TRAY AND STRAP SYSTEM FOR 24 QUART SYSTEM
Cool Shirt
 Cool Shirt Tube Connector Set
COOL SHIRT - SAFETY PULL RELEASE CONNECTORS SET - PAIR
Cool Shirt

Cool Shirt Tube Connector Set ▶

PART # ACC CS PRC-2
$48.00
 Cool Shirt Pro Air & Water System - 24 Quart
COOL SHIRT - PRO AIR & WATER SYSTEM COMPLETE - 24 QUART - The Pro Air & Water System comes with a 24 quart cooling unit with an internal pump that supplies temperature-controlled cool water to the shirt and HEPA-4 filtered, chilled air to your helmet via a 235 CFM blower. Eight feet of double insulated water hose with automatic shutoff/quick disconnects attach the shirt to the unit, and the Dual Temperature Control Switch allows the user to regulate the flow and the temperature of water for personal comfort based on external temperature variation. Total weight on this system is only nine pounds.

*COOL SHIRT IN SMALL-XX LARGE SOLD SEPARATELY
Cool Shirt
 Cool Shirt Connector & Drain Kit
COOL SHIRT - UNIVERSAL CONNECTOR AND DRAIN KIT - 6 PEICE KIT
Cool Shirt
 Front Bumper Cover - (2000-2002) PORSCHE Boxster S
Front Bumper Cover - (2000-2002) PORSCHE Boxster S (986s) M 008 - GENUINE PORSCHE - MSRP: $1064.00

+ Replaces PN: 986 505 311 04

+ USED ON OUR BOXSTER SPEC RACING (BSR) CARS
GENUINE PORSCHE
 Grille - Center Insert for Front Bumper Cover
Grille - Center Insert for Front Bumper Cover - (2000-2002) PORSCHE Boxster S (986S) M008 - Prime Coated - GENUINE PORSCHE - MSRP: $108.44

+ ALSO USED ON OUR BOXSTER SPEC RACING (BSR) CARS
GENUINE PORSCHE

Grille - Center Insert for Front Bumper Cover ▶

PART # BOD 986 505 551 00 G2X
$110.00
 BOD 986 LW HT
Hard Top Roof Skin Cover - (1997-2004) PORSCHE 986 Boxster - BSR / Racing - Lightweight Composite FB (14.50 Lbs.) - Batch Production - PATRICK MS USA

+ USED ON OUR BOXSTER SPEC RACING (BSR) CARS
+ Please contact us for special shipping arrangements

BOD 986 LW HT ▶

PART # BOD 986LWHT
Patrick Motorsports Exclusive
$1,175.00
 
BOXSTER LEXAN REAR WINDOW, RACING USE FOR LIGHT WEIGHT HARD TOPS ONLY
PATRICK MOTORSPORTS USA

Boxster lexan Rear Window ▶

PART # BOD 986RW
$37.55
 Body Cover Pin Set - Decklid Spoiler, Hood, Bonnet, Cover Hold Down Set
Body Cover Pin Set - Decklid Spoiler, Hood, Bonnet, Cover Hold Down Set - Includes lightweight threaded aluminum dome pins, Delrin receiver discs, lock pin clips and hardware - PATRICK MS USA
PATRICK MOTORSPORTS USA

Body Cover Pin Set - Decklid Spoiler, Hood, Bonnet, Cover Hold Down Set ▶

PART # BOD LID PIN KIT
Patrick Motorsports Exclusive
$48.00
 Brake Pad Set Front Boxster
BRAKE PAD SET - FRONT - PORSCHE BOXSTER THRU '04 - MOUNTING PARTS (1) 996 352 959 01 - KIT - GENUINE PORSCHE - LIST: $145.34
Textar

Brake Pad Set Front Boxster ▶

PART # BRA 986 351 939 15
$132.98
 BRA 986 352 403 01
BRAKE DISC - REAR LEFT / RIGHT - PORSCHE 986 BOXSTER S THRU '04 - 2 PER CAR - GENUINE - LIST: $155.96
GENUINE PORSCHE

BRA 986 352 403 01 ▶

PART # BRA 986 352 403 01
$148.16
 BRAKE PAD SET - REAR - PAGID RACING ORANGE RS4-4 - PORSCHE 986 BOXSTER / S THRU-'04 - CAYMAN / 996 CARRERA / S
BRAKE PAD SET - REAR - PAGID RACING ORANGE RS4-4 - PORSCHE 986 BOXSTER / S THRU-'04 - CAYMAN / 996 CARRERA / S - IDEAL FOR TOURING CAR, SHORT TRACK, LONG DISTANCE & SHOWROOM STOCK APPLICATIONS
Pagid
 BRA 99 5541 538
BRAKE PAD SET - FRONT - PAGID RACING ORANGE RS4-4 - PORSCHE 986 BOXSTER, CAYMAN - IDEAL FOR TOURING CAR, SHORT TRACK, LONG DISTANCE & SHOWROOM STOCK APPLICATIONS
Pagid

BRA 99 5541 538 ▶

PART # BRA 99 5541 538
$258.00
 BRA 996 355 139 01 SS
HOSE - BRAKE - STAINLESS STEEL BRAIDED – 911T '01-05, BOXSTER ALL, CARRERA & CARRERA 4, CARRERA S '05 ON, CARRERA S4 '06' 0N LIST-$59.95 (4 PER CAR)

BRA 996 355 139 01 SS ▶

PART # BRA 996 355 139 01 SS
$39.95
 CLU 986 116 911 00
CLUTCH KIT - DISC, PRESSURE PLATE & RELEASE BEARING - BOXSTER THRU '99 -
LIST $ 540.09 ALSO USED IN OUR BOXSTER SPEC RACING (BSR) CARS

CLU 986 116 911 00 ▶

PART # CLU 986 116 911 00
$563.45
 DRI 999 053 041 03
WHEEL BEARING PORSCHE, 911 TURBO '91 THRU 94' FRONT, CARRERA 2 &4 THRU '94, BOXSTER THRU '94 FRONT/REAR, BOXSTER S THRU '94 FRONT CARRERA & 4 '95 THRU 98' FRONT, 911 TURBO '96 THRU 97' FRONT CARRERA & 4 '99 THRU 05' FRONT EXCEPT "S"
SKF

DRI 999 053 041 03 ▶

PART # DRI 999 053 041 03
$69.06
 ELE 310 012
GAUGE - ENGINE OIL TEMP - VDO 2-1/8" COCKPIT 120-300 F. DEG. TEMP. GAUGE – (GREAT FOR A TRANS GAUGE)


ALSO USED ON OUR BOXSTER SPEC RACING (BSR) CARS
VDO

ELE 310 012 ▶

PART # ELE 310 012
$33.00
 ELE 323 057
VDO OIL TEMP SENDING UNIT 1/8"NPT, 0-300 F. DEG.

ALSO USED ON OUR BOXSTER SPEC RACING (BSR) CARS
VDO

ELE 323 057 ▶

PART # ELE 323 057
$12.00
 Battery Odyssey PC680
BATTERY ODYSSEY PC 680, 680 ranking amps for 5 seconds 595 cranking amps for 10 seconds 525 cranking amps for 20 seconds 17 amp hours Short circuit current over 1800A 25 minute reserve capacity with 25amp load Female brass terminal w/M6 SS bolt Length 7 1/16"
Width 3" Height 6 9/16" Weighs 14.5 lbs
Odyssey

Battery Odyssey PC680 ▶

PART # ELE BAT ODY PC680
$150.00
 Electrical Quick Disconnect Battery Terminal - Twist knob and cut off power to starter
Electrical Quick Disconnect Battery Terminal - Twist knob and cut off power to starter - Ideal for less frequently driven vehicles.
 Master Disconnect Switch - Battery - Alternator - Electrical
Electrical Master Disconnect Switch - 6 Pole Type with Alternator - FIA Approved

+ Includes installation instructions
+ Required for race cars, spec racing cars, BSR, Cup, etc.
 
BEARINGS - BELT PULLEY - BOXSTER

Belt Pulley Bearings Boxster ▶

PART # ENG 6203 2RS JEM
$19.25
 Intermediate Shaft Flange - 996 - Boxster
Intermediate Shaft Flange - PORSCHE (1997-2001) 996 Carrera / (1997-2001) Boxster / S - GENUINE PORSCHE - MSRP: $133.59
+ Updated Version with 4 mm Thick Seal
+ Also use: (Qty.) (1) 900 380 019 02 nut
GENUINE PORSCHE

Intermediate Shaft Flange - 996 - Boxster ▶

PART # ENG 996 105 017 02
$133.00
 ENG 996 106 037 51
RADIATOR/CENTER BOXSTER "S" THRU '04 CARRERA & CARRERA 4 TIPTRONIC '99 THRU "05
GENUINE PORSCHE

ENG 996 106 037 51 ▶

PART # ENG 996 106 037 51
$232.07
 ENG 996 106 132 51
RADIATOR/RIGHT FRONT BOXSTER & S THRU '04, CARRERA '99 THRU '05, CARRERA 4 '99 THRU '01 CARRERA 4 '02 THRU '05 EXCEPT "S
GENUINE PORSCHE

ENG 996 106 132 51 ▶

PART # ENG 996 106 132 51
$320.75
 ENG 996 106 665 57
WATER HOSE LEFT\RADIATOR UPPER, TO CENTER RADIATOR, BOXSTER S THRU 04' CARRERA & CARRERA 4 '99 THRU 05' TIPTRONIC
GENUINE PORSCHE

ENG 996 106 665 57 ▶

PART # ENG 996 106 665 57
$58.79
 ENG 996 106 666 55
WATER HOSE\ RT RADIATOR (LOWER) TO CENTER RADIATOR,BOXSTER S THRU 04', CARRERA & CARRERA 4 '99THRU 05' TIPTRONIC
GENUINE PORSCHE

ENG 996 106 666 55 ▶

PART # ENG 996 106 666 55
$35.00
 986 996 Engine Oil Cooler Heat Exchanger
Engine Oil Cooler Heat Exchanger - Porsche 996 All Except Turbo, 986 Boxster S - OEM BEHR, MSRP: $272.39

+ Use as high performance application to 1997-2004 Boxster 986 (Non S Models - M 96.20/22)
BEHR

986 996 Engine Oil Cooler Heat Exchanger ▶

PART # ENG 996 107 025 57
$228.00
 Engine Oil Pan & Sump Plate Baffle Kit - X51 996 Cup - BSR Boxster & Cayman
Engine Oil Pan & Sump Plate Baffle Kit - X51 / 996 Cup / BSR Boxster & Cayman - Application to all M96 - M97 engines - GENUINE PORSCHE MOTORSPORT

+ Superseded from PN: 996 107 988 00

+ Accusump system also recommended if running R-compound or race tires, as the deep sump will not add sufficient protection against starvation alone.
GENUINE PORSCHE PORSCHE MOTORSPORT
 
RADIATOR HARD LINE HOSE MODIFICATION FOR THE 986 BOXSTER SPEC. RACING SERIES (BSR)
PATRICK MOTORSPORTS USA

Radiator Hard Line Hose Boxster Spec ▶

PART # ENG PMP 986 BSR RHL
Patrick Motorsports Exclusive
$80.00
 Exhaust Muffler Silencer Set with Cat Bypass - 986 BSR - Boxster Spec Racing
Exhaust Muffler Silencer Set with Cat Bypass - 986 BSR - Boxster Spec Racing - (1997-1999) - PORSCHE 986 Boxster - Includes catalytic converter test pipes with O2 sensor port sockets, rear dual high flow mufflers, mounting system and gaskets. Tip exits through center license plate area on rear bumper cover - Fabricated Stainless Steel - PATRICK MS USA

+ Specially designed for BSR Racing and noise compliance. For Motorsport use only.

This system has been optimized tubing size and lengths for best overall efficiency with real time dyno testing and track racing. Proven performance with PATRICK MS BSR class winning racecars.

YOUTUBE:
http://www.youtube.com/playlist?list=PLf2v_QTalOPLz438CoWijBhgDl_FKBMzQ
PATRICK MOTORSPORTS USA

Exhaust Muffler Silencer Set with Cat Bypass - 986 BSR - Boxster Spec Racing ▶

PART # EXH 986 BSR MS
Patrick Motorsports Exclusive
$980.00
 FLU MOBIL1-1550W
ENGINE OIL - MOBILE ONE - SYNTHETIC - 15W50 - PERFORMANCE-RACE APPLICATIONS - INCLUDES DISPOSAL FEE FOR OLD OIL

FLU MOBIL1-1550W ▶

PART # FLU MOBIL1-1550W
$228.00
 Transmission Gear Lube Oil - SWEPCO 203
Gear Lube Oil - SWEPCO 203 - SAE 80W/90 - Includes Moly Additive - SWEPCO - Unit 1 Gallon
+ No Air Shipping Service (Ground Only)
SWEPCO
 Lightweight Flywheel - Aluminum Porsche Boxster & Cayman
Flywheel - Sport Lightweight Single Mass - (1997-2012) PORSCHE Boxster / Cayman / S - Billet Aluminum with replaceable friction surface - 13.75 Lbs. (6.24 Kg) - AASCO / PATRICK MS USA
+ Includes: Pilot Bearing, Torque Plate & Flywheel Bolts (Torque Spec: 60 ft lbs)

ALSO USED IN OUR BOXSTER SPEC RACING (BSR) CARS
AASCO
 Seal for Intermediate Shaft Flange
Seal for Intermediate Shaft Flange - (1999-2008) 996 - 997 / (1997-2008) BOXSTER / CAYMAN - OEM KACO - MSRP: $15.97

+ Notes: Late Type Seal (4 mm Thick) for Updated Flange # 996 105 017 01 or 996 105 024 01
+ Also use (Qty.) (3) 900 385 275 09 bolts (1) 999 707 392 40 o-ring
KACO

Seal for Intermediate Shaft Flange ▶

PART # GAS 996 105 112 01 KAC
$14.75
 Crankshaft Seal Front Boxster - 996
SEAL - CRANKSHAFT FRONT BOXSTER & "S" CARRERA & CARRERA 4 - LIST $19.17

Crankshaft Seal Front Boxster - 996 ▶

PART # GAS 999 113 475 40
$12.30
 Rear Main Seal - Boxster
REAR MAIN SEAL /FLYWHEEL 85 X105 X11 A.M./ BOXSTER & "S" CARRERA & CARRERA 4, CARRERA "S" & "S4"

Rear Main Seal - Boxster ▶

PART # GAS 999 113 490 40
$17.68
 Bolt - Flywheel to Clutch Pressure Plate (8 X 16 mm)
Bolt - Flywheel to Clutch Pressure Plate (8 X 16 mm) - 6 Per Car - GENUINE PORSCHE, MSRP: $0.91 / Each
GENUINE PORSCHE
 IGN 999 170 195 90
SPARK PLUG - BOSCH FR-6-LDC / 0 242 240 557 - LIST: $9.48

IGN 999 170 195 90 ▶

PART # IGN 999 170 195 90
$6.58
 Steering Wheel Hub Adapter - MOMO Italy
MOMO STEERING WHEEL ADAPTER HUB FOR PORSCHE BOXSTER 97-04, 944 ALL 85-89, 968 90-94, 964 & 993 90-04
MOMO
 Accusump Oil System PORSCHE Boxster Cayman
BOXSTER 986 BSR ACCUSUMP SYSTEM, INCLUDES OIL FILTER RELOCATION, OIL LINES, "CANTON" ACCUSUMP, OIL FILTER, & ALL HARDWARE FOR COMPLETE INSTALLATION, ALONG WITH PHOTO INSTRUCTIONS ON LAYOUT & USAGE, THIS IS THE ELECTRIC VALVE SYSTEM THAT WILL SAVE OIL PRESSURE AFTER SHUT DOWN, AND SUPPLY OIL PRESSURE AT START UP AS WELL AS UNDER HIGH G-LOAD SITUATION THAT CAN CAUSE OIL PUMP STARVATION THAT LEADS TO ENGINE FAILURE!

* CHECK OUT THE 986 BSR #17 & "RED" BSR FOR DETAILED INSTALLATION PHOTOS, OR CALL US REGARDING YOUR APPLICATION NEEDS.
PATRICK MOTORSPORTS USA Goodridge CANTON Racing Products LN ENGINEERING WIX

Accusump Oil System PORSCHE Boxster Cayman ▶

PART # OIL PKG 986 ACCUSUMP
Patrick Motorsports Exclusive
$1,200.00
 GT2 GT3 Control Arm Inner Section - Front Left / Right Lower
Control Arm (Inner Section) - Front Left / Right Lower - PORSCHE 911 GT2 / GT3 - GENUINE PORSCHE - MSRP: $302.66 + SPECIAL ORDER
GENUINE PORSCHE PORSCHE MOTORSPORT
 SUS 996 341 543 13
CONTROL ARM SHIMS (13MM)CARRERA 04-05 STREET FRONT/REAR TURBO 01-05 GT2 FRONT

ALSO USED IN OUR BOXSTER SPEC RACING (BSR) CARS
PATRICK MOTORSPORTS USA

SUS 996 341 543 13 ▶

PART # SUS 996 341 543 13
$7.50
 SUS 996 341 543 15
CONTROL ARM SHIMS (1.5MM) CARRERA 04-05 STREET FRONT/REAR TURBO 01-05 GT2 FRONT

ALSO USED IN OUR BOXSTER SPEC RACING (BSR) CARS
PATRICK MOTORSPORTS USA

SUS 996 341 543 15 ▶

PART # SUS 996 341 543 15
$5.75
 SUS 996 341 543 31
CONTROL ARM SHIMS (3.15MM)CARRERA 04-05 STREET FRONT/REAR TURBO 01-05 GT2 FRONT

ALSO USED IN OUR BOXSTER SPEC RACING (BSR) CARS
PATRICK MOTORSPORTS USA

SUS 996 341 543 31 ▶

PART # SUS 996 341 543 31
$6.00
 SUS 996 343 701 90
SWAY BAR\FRONT (EURO GT3 STREET VERSION) 27MM 5 WAY ADJ. NOTE: FOR ON U.S. CARS ALSO USE (2) 99634379216 BUSHINGS. EXISTING DROP LINKS MUST BE SHORTENED.

ALSO USED IN OUR BOXSTER SPEC RACING (BSR) CARS

SUS 996 343 701 90 ▶

PART # SUS 996 343 701 90
$424.94
 
SWAY BAR BUSHING FOR SWAY BAR SUS99634370190
ALSO USED IN OUR BOXSTER SPEC RACING (BSR) CARS

SUS 996 343 792 16 ▶

PART # SUS 996 343 792 16
$13.76
 
REAR TOE LINK SET (FULLY ADJUSTABLE) - FIT'S 986, 996, AND 987

ALSO USED ON OUR BOXSTER SPEC RACING (BSR) CARS

SUS 996TLNK ▶

PART # SUS 996TLNK
$553.85
 Momo Quick Release Steering Wheel Hub
MOMO Quick Release Rally Bolt On/STEERING WHEEL HUB
The new lightweight Quick Releases from MOMO feature a skyway design that saves time when it is crucial. The advanced design allows only one way of installation so that there is no more fumbling of trying to line up a SPLINE design. The MOMO system will also not gall like a SPLINE design does after hard use. This piece need to be welded on the steering column.

ALSO USED IN OUR BOXSTER SPEC RACING (BSR) CARS
MOMO
 Porsche GT2 GT3 Lower Control Arm Set Boxster Spec 986 996
Porsche GT2 / GT3 Lower Front / Rear Control Arm Set / 2 Piece Conversion Package for PORSCHE 996 / BOXSTER 986 / BSR / Spec Racing - GENUINE PORSCHE / PATRICK MS USA

+ Complete Set with adjustable camber shims including sizes: (Qty.) (2) 13, (4) 3.15 & (2) 1.50mm
+ Application of shims between outer & inner control arms will allow for adjustable camber capability over that of the original single piece control arm system. Achieving increased negative camber beyond (-1.8 Deg.) for better tire contact & handling is now possible.
+ BSR Class approved for front axle suspension only | BSX Class (Check latest regulations)
PATRICK MOTORSPORTS USA GENUINE PORSCHE

Porsche GT2 GT3 Lower Control Arm Set Boxster Spec 986 996 ▶

PART # SUS PKG SUS 996 986 FLC
Patrick Motorsports Exclusive
$1,195.00
 Steering Wheel - Series 7 MOMO Italy
MOMO MOD 7 STEERING WHEEL
3 DISHED SPOKES, 350 mm DISH DIMENSIONS: 70 mm, DESCRIPTION: MOMO RACING STEERING WHEELS FOR ALL RACING REQUIREMENTS. MATERIAL: ANTICORDAL ALUMINUM

ALSO USED IN OUR BOXSTER SPEC RACING (BSR) CARS
MOMO
 TIR 2254517TO
TOYO RACING TIRES 225/45/17 SERIES 888

ALSO USED ON OUR BOXSTER SPEC RACING (BSR) CARS

TIR 2254517TO ▶

PART # TIR 2254517TO
$282.86
 TIR 2554017TO
TOYO RACING TIRES 255/40/17 SERIES 888


ALSO USED ON OUR BOXSTER SPEC RACING (BSR) CARS

TIR 2554017TO ▶

PART # TIR 2554017TO
$261.42