(2000-2004) 2.7L H6 M96 Parts

Accusump Kit Porsche Boxster

986 BSR ACCUSUMP KIT, INCLUDES OIL FILTER RELOCATION, OIL LINES, "CANTON" ACCUSUMP, OIL FILTER, & ALL HARDWARE FOR COMPLETE INSTALLATION, ALONG WITH PHOTO INSTRUCTIONS ON LAYOUT & USAGE, THIS IS THE ELECTRIC VALVE SYSTEM THAT WILL SAVE OIL PRESSURE AFTER SHUT DOWN, AND SUPPLY OIL PRESSURE AT START UP AS WELL AS UNDER HIGH G-LOAD SITUATION THAT CAN CAUSE OIL PUMP STARVATION THAT LEADS TO ENGINE FAILURE !

* CHECK OUT THE 986 BSR #17 & "RED" BSR FOR DETAILED INSTALLATION PHOTOS, OR CALL US REGARDING YOUR APPLICATION NEEDS.

Engine Conversion Harness 993 3.6L DME

ENGINE CONVERSION HARNESS - PORSCHE 911 / 914 / 964 CHASSIS INTERFACE TO 3.6L (993) '95-'98 ENGINE CONTROL UNIT - FEATURES NEW ORIGINAL EQUIPMENT CONNECTIONS, FUEL PUMP RELAY, OBD II SCAN PORT AND CHECK ENGINE LIGHT WIRE - PATRICK MOTORSPORTS EXCLUSIVE
+ ALSO INCLUDES MODEL SPECIFIC CHASSIS JUMPER HARNESS FOR 911 CHASSIS

OUR HARNESSES MAKE YOUR ENGINE SWAPS A PLUG AND PLAY OPERATION, NO DAMMAGED COMPONANTS BY INCORRECT WIRING! ALSO RETAIN THAT FACTORY INSTALLED LOOK.

*ALSO INCLUDES 911 ENG. BAY JUMPER HARNESS

Oil Pressure Sending Unit - Dual Pole

OIL PRESSURE SENDING UNIT CONVERSION - DUAL POLE TYPE FOR OIL PRESSURE AND WARNING LIGHT - FOR USE WITH ENGINE CONVERSIONS - INCLUDES SENDING UNIT AND ADAPTOR FITTING - 10 BAR TYPE – DON’T RISK ENGINE DAMAGE BY MISSING AN OIL PRESSURE DROP. INSTALL THIS WITH OUR LOW OIL PRESSURE WARNING LIGHT **PMPSLOPWL**AND SAVE YOUR MOTOR.
*NOTE: DO NOT USE TEFLON TAPE - GROUND SOURCE

Spal Fan 5.2" Low Profile

5.2" Paddle Blade Low Profile Fan / 12V Pusher, VA31-A101-46S * 5.2"P/12V/SUM - SPAL USA

This fan works excellent with our line of Setrab Oil Coolers

Cool Shirt Cool Water Shirts in Blue

COOL SHIRT - COOL WATER SHIRT - BLUE - *HANS DEVICE COMPATIBLE - AVAILABLE IN SMALL, MEDIUM, LARGE, X-LARGE AND XX-LARGE *PLEASE SPECIFY SIZE WHEN ORDERING

Cool Shirt Club System 24 Quart

COOL SHIRT - CLUB SYSTEM COMPLETE - 24 QUART -SEPARATELY

The Club 24 System comes with a 24qt cooling unit with an internal pump which supplies cooled water to the shirt through 8ft of double insulated hose with automatic shutoff / quick disconnects. The optional Temperature Control Switch gives the driver complete control of their comfort while in their race car. Total weight for the Club System is only 4lbs. Available options include the Temperature Control Switch, SFI-approved FireWear® fire-retardant Cool Shirt®, Universal Drain Kit, Emergency Pull-Release Connectors and Mounting Tray with strap.

The Club Systems are the most popular driver system manufactured. The Club System 24 combines the advantage of Cool Shirt®’s temperature-controlled cooling power with hours of cooling time.

Ideal for those racing applications where space is not as much of an issue and the races may run long. Versatile enough to be perfect for everything from road courses to oval track racing, the Club 24 System keeps you cool and alert for the entire race when going the distance really counts.

** COOL SHIRT SOLD SEPARATELY

Cool Shirt - Temp Control Switch Kit

COOL SHIRT - TEMPERATURE CONTROL SWITCH - FLOW CONTROLLER

Cool Shirt Firewear Cool Water Shirt - Large Short Sleeve

COOL SHIRT - FIREWEAR COOL WATER SHIRT - LARGE - SHORT SLEEVE *HANS DEVICE COMPATIBLE

Cool Shirt Mounting Tray Kit for 24 Quart System

COOL SHIRT - MOUNTING TRAY AND STRAP SYSTEM FOR 24 QUART SYSTEM

Cool Shirt Tube Connector Set

COOL SHIRT - SAFETY PULL RELEASE CONNECTORS SET - PAIR

Cool Shirt Pro Air & Water System - 24 Quart

COOL SHIRT - PRO AIR & WATER SYSTEM COMPLETE - 24 QUART - The Pro Air & Water System comes with a 24 quart cooling unit with an internal pump that supplies temperature-controlled cool water to the shirt and HEPA-4 filtered, chilled air to your helmet via a 235 CFM blower. Eight feet of double insulated water hose with automatic shutoff/quick disconnects attach the shirt to the unit, and the Dual Temperature Control Switch allows the user to regulate the flow and the temperature of water for personal comfort based on external temperature variation. Total weight on this system is only nine pounds.

*COOL SHIRT IN SMALL-XX LARGE SOLD SEPARATELY

Cool Shirt Connector & Drain Kit

COOL SHIRT - UNIVERSAL CONNECTOR AND DRAIN KIT - 6 PEICE KIT

Photo Radar License Plate Shield

LICENSE PLATE SHIELD - "SUPER PROTECTOR" - NO TICKET ANTI-PHOTO PLATE PROTECTOR - DOMESTIC CAR - LIST: $39.95

ACC038-RAGGTOPP

RAGGTOPP FABRIC CONVERTIBLE TOP CLEANER AND PROTECTANT KIT - LIST: $34.99

Computer Balancing

ROTATIONAL BALANCE OPERATIONS - CERTIFIED COMPUTERIZED BALANCING SERVICE
+ SERVICE INCLUDED AT NO CHARGE WITH COMPLETE FLYWHEEL AND CLUTCH SYSTEMS

Battery - ODYSSEY PC-925-A

Battery - ODYSSEY PC-925-A - 7.00D X 6.625W x 5.00T - 26 Lbs. - 925 Cranking Amps for 5 Secs. - Terminal: M6 for automotive - ENERSYS (0765-2024) - MSRP: $240.74

BEL 676 51048 241

SERPENTINE BELT - BOXSTER -FOR CUSTOM PULLEY DESIGNED FOR THE BOXSTER SPEC RACING SERIES (BSR) PART NUMBER PMPBSRCUP

Latch Rubber Draw T-Handle

LATCH - RUBBER DRAW - SMALL T- HANDLE (69.0mm O.A.) - AIRCRAFT QUALITY WITH STAINLESS STEEL HARDWARE

License Plate Light

LICENSE PLATE LIGHT - 2 PER CAR - INCLUDES RUBBER MOUNTING GASKET KIT - CHROME - HELLA - LIST: $83.25

BOD 986 505 311 04

FRONT BUMPER COVER BOXSTER S THRU 02 USED ON OUR BOXSTER SPEC RACING (BSR) CARS

Porsche Hood Emblem Crest Kit - Gold Type

Porsche Hood Emblem Crest Kit - Gold Type - GENUINE PORSCHE
+ Includes base seal and nut set

BOD 996 575 141 02

RADIATOR AIR DUCT/ FRONT BUMPER TO COOLER

BOD LIDPINKIT

DECK LID PIN KIT - HOLD DOWN SET INCLUDES SPECIALLY MACHINED DELRIN STRIKER DISCS, ALUMINUM PINS, AND LOCKING CLIPS - LIGHTWEIGHT - PATRICK MS EXCLUSIVE

TILTON ADJUSTABLE BRAKE PROPORTION VALVE

TILTON ADJUSTABLE BRAKE PROPORTION VALVE - 7 POSITION LEVER TYPE - 10 MM X 1 MM PORT THREADS - ALUMINUM WITH BLACK ANODIZED FINNISH

SOCKET PIECE - 90 DEG. BRAKE BANJO FITTING

SOCKET PIECE - 90 DEG. BRAKE BANJO FITTING - PORSCHE - 10 MM x 1.0 MM - FOR CARS WITHOUT BRAKE BOOSTER - LIST: $18.88

Brake Disc Rotor Front Boxster

BRAKE DISC ROTOR - FRONT - PORSCHE BOXSTER 986 THRU '04 - 2 PER - LIST: $220.50

Brake Pad Set Front Boxster

BRAKE PAD SET - FRONT - PORSCHE BOXSTER THRU '04 - MOUNTING PARTS (1) 996 352 959 01 - KIT - GENUINE PORSCHE - LIST: $145.34

Brake Disc Rotor Rear Boxster

BRAKE DISC - REAR - PORSCHE BOXSTER 986 THRU '04 - 2 PER CAR - - LIST: $249.50

Brake Shoe Set Parking Brake

BRAKE SHOE SET FOR PARKING BRAKE BOXSTER THRU '04 LIST $134.67

BRAKE PAD SET - REAR - PAGID RACING ORANGE RS4-4 - PORSCHE 986 BOXSTER / S THRU-'04 - CAYMAN / 996 CARRERA / S

BRAKE PAD SET - REAR - PAGID RACING ORANGE RS4-4 - PORSCHE 986 BOXSTER / S THRU-'04 - CAYMAN / 996 CARRERA / S - IDEAL FOR TOURING CAR, SHORT TRACK, LONG DISTANCE & SHOWROOM STOCK APPLICATIONS

Brake Pad Set Rear Boxster

BRAKE PAD SET - REAR - PORSCHE 986 BOXSTER / S THRU '04 / 911 CARRERA '99-'05 / CARRERA 4 '99-'05 - MOUNTING PARTS: 1 QTY: 996 352 949 01 - GENUINE - LIST: $128.35

Brake Pad Set

BRAKE PAD SET- PORSCHE 996 TURBO '01-'05 REAR, CARRERA & CARRERA 4 '99-'05 FRONT,CAYMAN"S" FRONT, BOXSTER"S" FRONT - ALSO USE MOUNT PARTS: 1 QTY 996 351 959 01 KIT -

BRA 996 355 139 01 SS

HOSE - BRAKE - STAINLESS STEEL BRAIDED – 911T '01-05, BOXSTER ALL, CARRERA & CARRERA 4, CARRERA S '05 ON, CARRERA S4 '06' 0N LIST-$59.95 (4 PER CAR)

BRA 996 612 365 00 P

WEAR SENSOR - LEFT / RIGHT BRAKE PAD - 986 BOXSTER & BOXSTER "S" FRONT THRU '04 ,CARRERA & 4 '99-'05 FRONT & REAR, CARRERA & 4 FROM '05 REAR, 911 TURBO '01-'05 FRONT & REAR PEX - LIST: $17.19

Brake Pad Set - Boxster Race - Front

BOXSTER FRONT PAD SET, DTC-05 RACE COMPOUND

Brake Pad Set - Boxster Race - Rear

BOXSTER REAR PAD SET, DTC-05 RACE COMPOUND

CLU 012 141 165 E

RELEASE BEARING - CLUTCH RELEASE - PORSCHE BOXSTER THRU '06 / CAYMAN / S - SACHS - LIST: $61.06

CLU 88 1864 959

CLUTCH DISC - SPORT RIDGED HUB - PORSCHE BOXSTER / S THRU '06 / CAYMAN FROM '07 / CAYMAN S FROM '06 - ORGANIC LINING HIGHER FRICTION - SACHS RACE ENGINEERING - LIST: $975.21

CLU 88 3082 754

PRESSURE PLATE - SPORT - BOXSTER 986 / S THRU '07 / CAYMAN / S -'07 / CARRERA 996 '02-'05 - SACHS RACE ENGINEERING - LIST: $1137.77

Clutch Pressure Plate - "Sport" 986 / 996

Clutch Pressure Plate - "Sport" - (1997-2008) 986 BOXSTER / 987c CAYMAN / (2002-2005) 996 - SACHS PERFORMANCE

CLU 986 115 028 03

PRESSURE PLATE - BOXSTER Thru '99 - GENUINE

Clutch Release Bearing - PORSCHE Boxster S / 996

Clutch Release Bearing - PORSCHE Boxster S / 996 - OEM SACHS (SBA60115) - MSRP: $169.36

Clutch Pedal Spring (Power Spring)

Clutch Pedal Spring (Power Spring) - Purple Spring Type - GENUINE PORSCHE MOTORSPORT

+ Applies to 2000-2004 Porsche 986s / Boxster S
+ 1999 Porsche 996 Use also PN: 996 423 139 10 - Clutch Pedal

DRI 999 053 041 03

WHEEL BEARING PORSCHE, 911 TURBO '91 THRU 94' FRONT, CARRERA 2 &4 THRU '94, BOXSTER THRU '94 FRONT/REAR, BOXSTER S THRU '94 FRONT CARRERA & 4 '95 THRU 98' FRONT, 911 TURBO '96 THRU 97' FRONT CARRERA & 4 '99 THRU 05' FRONT EXCEPT "S"

Wheel Bearing Front - Rear

WHEEL BEARING - FRONT/REAR -BOSXTER FROM '05 FRONT & REAR BOXSTER "S" THRU '04 REAR BOXSTER "S" FROM '05 FRONT & REAR CAYMAN & "S" FRONT & REAR CARRERA 4"S" '02-'05 FRONT CARRERA '99-''05 GT3 CUP FRONT 911 TURB0 '01-"05 FRONT CARRERA & S,4 FROM '05 FRONT
LIST $ 107.90

ELE 0 258 006 MOT

OXYGEN SENSOR - 6 WIRE (TYPE LSU4) WIDE BAND OXYGEN SENSOR FOR RACING APPLICATION - USED WITH MOTEC OR ZYTECH MANAGEMENT SYSTEM - LIST: $226.79

Reverse Light Switch Porsche Transmission

REVERSE LIGHT SWITCH - MANUAL TRANSMISSION - PORSCHE - FROM 356 TO 97 TURBO
GENUINE - LIST: $96.43

ELE BQD-X

BATTERY DISCONNECT TERMINAL END KIT - SIMPLY UNSCREW THE GREEN KNOB TO DISCONNECT BATTERY POWER - A MUST FOR LESS FREQUENTLY DRIVEN CARS

ELE CREADER IV

DTC READER - DIAGNOSTIC TROUBLE CODE READER - OBD II & E OBD / INCLUDING CAN PROTOCOL *
Features:
1. LCD display
2. Display the content of trouble code
3. FREEZE FRAME function
4. Supporting CANBUS diagnosis
5. Manual reading code and clearing code

Specifications
1. LCD display(128*32), displaying by 2 lines, LED backlight
2. Two keys operation
3. Enclosed a disc, including most manufacturer code information. Now there is more than 7000 manufacturer codes, and it updates continuously.
4. Enclosed users' manual, including the explanation of trouble code before 1000 number.

ELE M880

COMPLETE MOTEC SYSTEM SOLUTIONS FOR PORSCHE MOTORSPORT APPLICATION - PLEASE CONTACT US FOR SYSTEM EVALUATION - THE APPLICATIONS GUIDE IS AVAILABLE FOR DOWNLOAD IN THE CATALOGS SECTION ON OUR WEBSITE

ELE RCX11862

MASTER DISCONNECT SWITCH - POWER - 6 POLE TYPE WITH ALTERNATOR - (FIA APPROVED) *Required for race cars


ALSO USED ON OUR BOXSTER SPEC RACING (BSR) CARS

ELE TIL 40-524

TILTON OIL / WATER PUMP - USED ON TRANSAXLE COOLER SYSTEMS - LIGHTWEIGHT - 3/8" NPT INLET / OUTLET - 12 VOLT - BUNA - INCLUDES BYPASS - 60 PSI WORKING PRESSURE - 1-2 GPM FLOW RATE

ELE UN6627400

HELLA AIR HORN SET - HIGH AND LOW TONE - INCLUDES ELECTRIC AIR PUMP & RELAY, COMPLETE KIT WITH HARDWEARE FOR INSTALLATION - LIST: $59.05

* A MUST FOR A FAST CAR IN SLOWER TRAFFIC !

Engine Oil Deep Sump Kit

Deep Sump Kit - .50 Qt - Including Pickup Tube Extension - PORSCHE 996, 986 Boxster - M96/M97 MY97, LN ENGINEERING, MSRP: $282.95

LN Engineering’s deep sump kit increases total oil capacity by .5 Qt. This reduces the chances of oil starvation due to prolonged cornering, acceleration, and high speed operation. The kit lowers the sump as well as the pickup tube while increasing oil capacity to accomplish this. Available for M96 and M97 engines (not for GT2, GT3, or Turbo engines).

Kit includes sump spacer, oil baffle spacer, and oil pickup tube extension, o-ring for pickup tube extension, as well as all required hardware needed for installation.

Accusump also recommended if running R-compound or race tires, as the deep sump will not add sufficient protection against starvation alone.

Additional Information:
http://www.lnengineering.com/store/catalog/deep-sump-including-pickup-tube-extension-p-108.html

Engine Oil Sump Kit (+ 2.0 Qt. Deep Sump Extension)

Engine Oil Sump Kit (+ 2.0 Qt. Deep Sump Extension, Pickup Tube Ext., Baffle & Windage Tray) - PORSCHE 996, 986 Boxster - M96/M97 MY97, LN ENGINEERING, MSRP: $852.79
+ Note: 1 inch lower than the stock sump plate. Provides 2.0 quarts additional oil capacity. Includes pick-up tube extension, windage tray, baffle, and Loctite sealant. Requires clearance modification to the engine protection pan.

LN Engineering’s deep sump kit increases total oil capacity by 2 Qt. This reduces the chances of oil starvation due to prolonged cornering, acceleration, and high speed operation. The kit lowers the sump as well as the pickup tube while increasing oil capacity to accomplish this. Available for M96 and M97 engines (not for GT2, GT3, or Turbo engines).

Kit includes sump spacer, oil baffle spacers, EBS Racing X51 oil baffle, windage tray (to prevent sloshing of oil), 997/Cayman oil returns (2 qt sump not compatible with 996 swirl pots) and oil pickup tube extension, o-ring for pickup tube extension, sealant, as well as all required hardware needed for installation.

Recommended for track use only due to reduced ground clearance. Fabrication and use of a skid plate to protect sump recommended as well. A good alternative to an Accusump for those wanting a simpler installation to prevent oil starvation when paired with our tandem oil scavenge pump kit.

Engine Mount Sport L

ENGINE MOUNT - LEFT - PORSCHE 911 TURBO '91-'94 / 911 CARRERA 4 THRU '94 TARGA / CABRIO / 911 CARRERA '95-'98 / CAN BE USED AS SPORT MOUNT (FIRMER RUBBER) ON C2 & C4 COUPE - CORTECO-CFW - LIST: $366.05

Engine Mount Sport R

ENGINE MOUNT - RIGHT - PORSCHE 911 TURBO '91-'94 / 911 CARRERA 4 THRU '94 TARGA / CABRIO / 911 CARRERA '95-'98 / CAN BE USED AS SPORT MOUNT (FIRMER RUBBER) ON C2 & C4 COUPE - CORTECO-CFW - LIST: $366.05

Intermediate Shaft Flange - 996 - Boxster

Intermediate Shaft Flange - PORSCHE (1997-2001) 996 Carrera / (1997-2001) Boxster / S - GENUINE PORSCHE - MSRP: $133.59
+ Updated Version with 4 mm Thick Seal
+ Also use: (Qty.) (1) 900 380 019 02 nut

Intermediate Shaft Flange

Intermediate Shaft Flange - PORSCHE 996 Carrera / Boxster / S - GENUINE PORSCHE - MSRP: $133.59

+ Updated Version with 4 mm Thick Seal
+ For Original Intermediate Shaft - Marked: 996 105 901 002
+ Also use: (Qty.) (1) 900 380 019 02 nut

ENG 996 106 011 55

WATER PUMP ASSEMBLY - PORSCHE BOXSTER&"S" thru '04 CARRERA & CARRER"4" '99 THRU '05 - REQUIRES GASKET - PART NUMBER SUPERSEDED TO 996 106 011 55 - GENUINE - LIST: $313.85

ENG 996 106 037 51

RADIATOR/CENTER BOXSTER "S" THRU '04 CARRERA & CARRERA 4 TIPTRONIC '99 THRU "05

ENG 996 106 132 51

RADIATOR/RIGHT FRONT BOXSTER & S THRU '04, CARRERA '99 THRU '05, CARRERA 4 '99 THRU '01 CARRERA 4 '02 THRU '05 EXCEPT "S

ENG 996 106 665 57

WATER HOSE LEFT\RADIATOR UPPER, TO CENTER RADIATOR, BOXSTER S THRU 04' CARRERA & CARRERA 4 '99 THRU 05' TIPTRONIC

ENG 996 106 666 55

WATER HOSE\ RT RADIATOR (LOWER) TO CENTER RADIATOR,BOXSTER S THRU 04', CARRERA & CARRERA 4 '99THRU 05' TIPTRONIC

986 996 Engine Oil Cooler Heat Exchanger

Engine Oil Cooler Heat Exchanger - Porsche 996 All Except Turbo, 986 Boxster S - OEM BEHR, MSRP: $272.39

+ Use as high performance application to 1997-2004 Boxster 986 (Non S Models - M 96.20/22)

Crank Ventilation Socket Port

SOCKET PORT - CRANKCASE VENTILATION - PORSCHE BOXSTER - GENUINE

ENG 996 107 237 52

OIL SEPARATOR BOOT(BELLOWS) BOXSTER THRU '04, BOXSTER S THRU '04 , CARRERA & CARRERA 4 THRU 01'

Engine Oil Pan & Sump Plate Baffle Kit - X51 996 Cup - BSR Boxster & Cayman

Engine Oil Pan & Sump Plate Baffle Kit - X51 / 996 Cup / BSR Boxster & Cayman - Application to all M96 - M97 engines - GENUINE PORSCHE MOTORSPORT

+ Superseded from PN: 996 107 988 00

+ Accusump system also recommended if running R-compound or race tires, as the deep sump will not add sufficient protection against starvation alone.

ENG 999 070 362 40

O-RING FOR OIL SEPARATOR BOXSTER THRU '04, BOXSTER S THRU '04 , CARRERA & CARRERA 4 THRU 01'

ENG 999 707 389 40

O-RING FOR OIL COOLER 26 X 3 MM BOXSTER & BOXSTER S THRU 04' (2 PER CAR) CARRERA & CARRERA 4 '99 THRU 05' ( PER CAR) ,911 TURBO '01THRU 05' (4 PER CAR)

ENG 999 707 409 40

O-RING FOR OIL COOLER 26 X 3 MM BOXSTER & BOXSTER S THRU 04' (2 PER CAR) CARRERA & CARRERA 4 '99 THRU 05' ( PER CAR) ,911 TURBO '01THRU 05' (4 PER CAR)

EXH 99 1010 207

EXHAUST MUFFLER SET - SPORT - PORSCHE 911 '99-'05 - POLISHED STAINLESS STEEL - NOTE: ALSO USE TIP SET 99 1022 115 - TUV APPROVED - DANSK

Engine Oil Filter - WIX Racing

Engine Oil Filer - Spin On Type - WIX RACING (51060R) + Replacement for FRAM HP4

FIL 996 107 225 53 ML

FILTER KIT - ENGINE OIL - PORSCHE - FILTER CARTRIDGE AND HOUSING SEAL - MAHLE 0X128 D - LIST: $22.52

Air Filter - Engine 986 Boxster

FILTER - ENGINE AIR - PORSCHE 986 BOXSTER / S THRU '04 - LIST: $40.64

FIL 996 110 253 01 ML

FILTER - FUEL - PORSCHE 986 BOXSTER / S THRU '01 / 911 CARRERA '99-'01 - MAHLE KL 80 - LIST: $46.28

Brake Fluid Pentosin Racing

BRAKE-P/S FLUID - PENTOSIN RACING - EXCEEDS DOT 4 SPEC - 1 LITER
Pentosin Racing Brake Fluid especially appropriate for racing cars as well as for passenger cars with reduced cooling air flow; this fluid not only exceeds the DOT 4 specifications but as far as the boiling point is concerned, it also exceeds the 5.1 specifications.

Red Line Gear Oil 75W 90

GEAR OIL -REDLINE 75W 90 HIGH PERFORMANCE SYNTHETIC. IMPROVES DRIVE LINE EFFICIENCY FROM 2 TO 5 % PER QT

FLU 83522 80204

WATER WETTER - RED LINE - SUPER COOLANT - 12 OZ BOTTLE THIS ADDITIVE WILL DROP YOUR COOLANT TEMP 10 -20 DEGREES.

FLU MOBIL1-1550W

ENGINE OIL - MOBILE ONE - SYNTHETIC - 15W50 - PERFORMANCE-RACE APPLICATIONS - INCLUDES DISPOSAL FEE FOR OLD OIL

Pilot Bearing Boxster Cayman

PILOT BEARING - '97-'07 PORSCHE BOXSTER/S - CAYMAN/S - INA PORSCHE - LIST: $70.31

Lightweight Flywheel - Aluminum Porsche Boxster & Cayman

FLYWHEEL - ALUMINUM LIGHT WEIGHT TYPE - PORSCHE BOXSTER & S '97-'08 & CAYMAN & S 99-08 RS 60 SPIDER 08 - SINGLE MASS TYPE - WEIGHT 13.75 LBS - INCLUDES PILOT BEARING AND HARDWARE

ALSO USED IN OUR BOXSTER SPEC RACING (BSR) CARS

Fuel Pressure Regulator (4.0 bar)

Fuel Pressure Regulator (4.0 bar) - OEM BOSCH (078 133 534 C) - MSRP: $180.00
+ Replacement for original equipment regulators (3.8 Bar) found on (1995-On) PORSCHE, 993, Boxster & 996
+ Use for increased fuel enrichment on high performance engine applications.
+ For Adjustable Type, Use PN: FUE 5271

Fuel Pressure Regulator - Adjustable Type (1.7 to 5.4 bar)

Fuel Pressure Regulator - Adjustable Type 1.7 to 5.4 Bar (19 to 90 PSI) - Preset at 3.0 Bar (43.50 PSI) - BOSCH / PATRICK MS USA
+ Replacement for original equipment regulators (3.8 Bar) found on (1995-On) PORSCHE, 993, Boxster & 996
+ Use for increased fuel enrichment on high performance engine applications.

Seal for Intermediate Shaft Flange

Seal for Intermediate Shaft Flange - (1999-2008) 996 - 997 / (1997-2008) BOXSTER / CAYMAN - OEM KACO - MSRP: $15.97

+ Notes: Late Type Seal (4 mm Thick) for Updated Flange # 996 105 017 01 or 996 105 024 01
+ Also use (Qty.) (3) 900 385 275 09 bolts (1) 999 707 392 40 o-ring

GAS 999 707 215 40

O-RING SEAL - SPARK PLUG TUBE - OUTER - PORSCHE BOXSTER 986/S THRU '04 / 911 CARRERA 2/4 '99-'01 - 6 PER CAR - GENUINE - LIST: $3.35

Thermostat O-Ring Engine Oil

O-RING - ENGINE OIL THERMOSTAT - PORSCHE 911 - 39.2 X 3 MM

Intermediate Shaft Cover O-Ring

O-RING - INTERMEDIATE SHAFT COVER PLATE - PORSCHE 911 '83-'98 / 911 TURBO '84-'97 - GREEN VITON - VICTOR REINZ - LIST: $1.92

GAS 999 707 343 40

O-RING SEAL - SPARK PLUG TUBE - INNER - PORSCHE BOXSTER 986/S THRU '04 / 911 CARRERA 2/4 '99-'01 - 6 PER CAR - GENUINE - LIST: $1.13

GAS 999 707 362 40

O-RING FOR OIL SEPARATOR (BOXSTER)

Oil Separator Vent O-Ring

O-RING FOR OIL SEPARATOR VENT LINE 18X2.5MM BOXSTER THRU '04, BOXSTER S THRU '04 , CARRERA & CARRERA 4 THRU 01

Oil Cooler O-Ring Porsche Boxster

O-RING FOR OIL COOLER 26 X 3 MM BOXSTER & BOXSTER S THRU 04' (2 PER CAR) CARRERA & CARRERA 4 '99 THRU 05' (2 PER CAR) ,911 TURBO '01THRU 05' (4 PER CAR)

GAS 999 707 446 40

O-RING FOR OIL SEPARATOR VENT LINE 18X2.5MMBOXSTER THRU '04, BOXSTER S THRU '04 , CARRERA & CARRERA 4 THRU 01'

AN-12 Hose End - 45 Degree

HOSE END - AN-12 TO 45 DEGREE SWIVEL - ALUMINUM - GOODRIDGE

Union Adapter Fitting (M30 Male to AN-12 Male)

Union Adapter Fitting (M30 Male to AN-12 Male) - ST JIC-Metric - Billet Aluminum Anodized - GOODRIDGE, MSRP: $59.91

Bolt - Flywheel to Clutch Pressure Plate (8 X 16 mm)

Bolt - Flywheel to Clutch Pressure Plate (8 X 16 mm) - 6 Per Car - GENUINE PORSCHE, MSRP: $0.91 / Each

Breather Hose Cloth Braided 24mm ID - Oil - Crank Ventilation

Breather Hose - 24mm I.D. - Cloth braided - Used for engine to oil tank - GERMAN
UNIT: .20 Qty. = 1 Meter

Brake Hardware Kit Boxster Cayman

HARDWARE KIT FOR BRAKE PADS BOXSTER & "S" ALL CAYMAN FRONT & REAR CAYMAN CARRERA '99-'05 REAR CARRERA 4 '99-'05 GENUINE

Wheel Stud M14x60MM

WHEEL STUD 14 X 1.5 X 60MM

Wheel Spacer Set 7mm

WHEEL SPACERS - 7MM - 911 914 930 986 993 996 997

INT93555-12BAPD

RACING HARNESS 5 PT KIT, 3", CAM,GN,BOLT ADJ.,PD SEWN LAP(BOLT) , GRAND NATIONAL STYLE. SHLDR(WRAP), SINGLE SUB (BOLT),SFI 16.1, BLACK

Seat Side Mount

SEAT SIDE MOUNTS ANODIZED - SET

Oil Breather Catch Tank - 4.65 Inch (118mm) O.D.

Oil Breather Catch Tank - 4.65 Inch (118mm) O.D. - Lightweight Spun Aluminum with Internal Baffling - 2) AN-12 Female Ports & AN-06 Drain Plug - PETERSON FLUID SYSTEMS
+ Includes: Insulated Stainless Steel Mounting Strap

In Line Filter Oil-Fuel AN-08

SCAVENGE FILTER - AN-08 INLINE BILLET ALUMINUM FILTER, WE USE THIS ON ALL OUR TRANSMISSIONS COOLING SYSTEMS, IT KEEPS METAL FRAGMENTS FROM RUNNING THROUGH THE OIL PUMP, COOLER AND BACK INTO THE GEARS, OUCH ! YES, THIS IS A KEY INGREDIENT TO YOUR TRANSMISSIONS LONG LIFE - PETERSON FLUID SYSTEMS

Inline Filter - Oil / Fuel - AN-12

INLINE FILTER - OIL OR FUEL - STAINLESS STEEL FILTER ELEMENT RATED AT 60 MICRON OR .0023 INCH CAPTURE PARTICLE SIZE - AN-12 IN & OUT - BILLET ALUMINUM HOUSING - RED ANODIZED - PETERSON - LIST: $183.34

Adapter Fitting - (M22 to AN-08) - For ProLine Oil Coolers

Adapter Fitting - (M22 to AN-08) - For ProLine Oil Coolers - Billet aluminum black anodized - Includes o-ring seal - SETRAB - MSRP: $11.00

Adapter Fitting - (M22 to AN-10) - For ProLine Oil Coolers

Adapter Fitting - (M22 to AN-10) - For ProLine Oil Coolers - Billet aluminum black anodized - Includes o-ring seal - SETRAB - MSRP: $11.00

Adapter Fitting - (M22 to AN-12) - For ProLine Oil Coolers

Adapter Fitting - (M22 to AN-12) - For ProLine Oil Coolers - Billet aluminum black anodized - Includes o-ring seal - SETRAB - MSRP: $12.00

Adapter Fitting - (M22 to AN-16) - For ProLine Oil Coolers

Adapter Fitting - (M22 to AN-16) - For ProLine Oil Coolers - Billet aluminum black anodized - Includes o-ring seal - SETRAB - MSRP: $14.00

Setrab Oil Cooler Mounting Kit - 23-6002

SETRAB 6 SERIES OIL COOLER MOUNTING KIT, LIST $44.00

ProLine Mounting Bracket kits are lightweight rib-reinforced aluminum and Baja-tested. Hardy bulkhead mounting orientation incorporates 70A durameter dampening pads to completely isolate the cooler from vibration. Mounting brackets are sold in pairs, with all associated hardware.

Setrab Oil Cooler Mounting Kit

SETRAB 9 SERIES OIL COOLER MOUNTING KIT, LIST $ 50.00

ProLine Mounting Bracket kits are lightweight rib-reinforced aluminum and Baja-tested. Hardy bulkhead mounting orientation incorporates 70A durameter dampening pads to completely isolate the cooler from vibration. Mounting brackets are sold in pairs, with all associated hardware.

OIL SET50-110-7612

SETRAB OIL COOLER, SIZE 6-1/2" x 3" x 2", 22mm x 1.5, LIST $ 132.00 ***GREAT POWER STEERING & TRANS COOLER!

Oil Cooler | 6.42 x 3.93 x 1.83 Inch

SETRAB OIL COOLER, SIZE 6.42" x 3.93" x 1.83", 22mm X 1.5, LIST $ 146.00

OIL SET50-619-7612

SETRAB OIL COOLER, SIZE 11.25" X 5.75" X 2.0", 22mm x 1.5, LIST $214.00

Setrab Oil Cooler 50-920-7612

SETRAB OIL COOLER, SIZE 16" x 6" x 2", 22mm x 1.5, LIST $ 256.00

Setrab Oil Cooler 50-925-7612

SETRAB OIL COOLER, SIZE 16" x 7-1/2" x 2", 22mm x 1.5, $ 320.00

Remote Oil Filter Console Mount Set - AN-12

Remote Oil Filter & Console Mount Set - Includes modular mounting bracket, fittings & filter kit - Billet Aluminum, Black Finish - SETRAB / WIX RACING / PATRICK MS USA
+ Includes 2) PN: 22-ORB10AN12-00 - Adapter fitting - AN-10 ORB female to AN-12 Male
+ Includes 1) PN: 51060R - WIX Racing Filter

Screw Plug Adapter - M24x1.50 Male to 3/8 Inch NPT Female Port

Screw Plug Adapter - M24x1.50 Male to 3/8 Inch NPT Female Port - (1997-2005 ) 986 Boxster / (1982-1991) 944 / 944 2 / (1976-1988) 924 / 924 S - Used for transmission oil return / sump system - CAD Plated Steel - PATRICK MS USA

Mount Set Solid

MOUNT SET - ENGINE / TRANSMISSION - SPORT / RACE - PORSCHE 911 / TURBO '91-'05 / GT2 / BOXSTER '97-'05 / CAYMAN - SOLID TYPE - BILLET ALUMINUM - ANODIZED - 1 SET PER CAR.

THIS MOUNT SET WILL GIVE YOU RESPONSIVE HANDLING AND BETTER TRACK FEEL THAN THE STOCK RUBBER MOUNTS

*RECOMMENDED FOR RACING USE- ALSO USED ON OUR BOXSTER SPEC RACING (BSR) CARS

-PATRICK MOTORSPORTS EXCLUSIVE --

PMP SB12175

STEEL WELD IN BUNG 12x1.75mm

Front Mount Oil Cooler - 500 COM - GT / RS / RSR - Competition Single Pass

Front Mount Oil Cooler - 500 COM - GT / RS / RSR - Competition Single Pass - 4x) 3/4 NPT Ports - Size: 23.50 x 5.50 x 2.25 Inches (59.69 x 13.97 x 5.72 cm) - Black Finnish - Includes Mounting Braces - SETRAB / PATRICK MS USA EXCLUSIVE
+ Specially Designed Production - Manufactured by Setrab of Sweden

* WE USE THIS COOLER ON ALL OUR HIGH PERFORMANCE & FULL RACE 914, 911, & 930 TURBO PROJECTS. THE SETRAB OIL COOLERS ARE ONE OF THE FINEST MADE, THEY ARE LIGHTWEIGHT AND THIS MEANS THEY COOL BETTER! THEY DISSIPATE OIL TEMPERATURE BETTER THAN MOST COMMON OIL COOLERS. THIS COOLER IS SET UP WITH 3/4" NPT FITTINGS 2) ON EACH END, THE FITTINGS SHOWN ARE NOT INCLUDED, BUT WE ARE ALSO A FULL LINE GOODRIDGE DISTRIBUTOR, ASK FOR THE PLUMBING HARDWARE FOR YOUR APPLICATION AND SEE IT IN USE ON MANY CARS IN THE "PROJECT" SECTION ON OUR SITE. ADDING AN EXTRA OIL COOLER TO YOUR PORSCHE WILL INCREASE PERFORMANCE AND LENGTHEN THE SERVICE LIFE OF YOUR ENGINE. THIS IS A SMALL INVESTMENT FOR HUGH PIECE OF MIND. PLEASE CALL FOR QUOTES ON ALL OUR OTHER SYSTEMS.

Crankshaft Pulley Kit (For cars with AC)

Crankshaft Pulley Kit (For cars with AC) - Sport / Motorsport - Accessory underdrive pulley with multi-rib belt - PORSCHE Boxster / Cayman / 996 / 997 / GT3 Upto-05 | Billet Aluminum Black Anodized - PATRICK MS USA EXCLUSIVE
+ Replaces PN: 996 102 115 63 - Pulley
+ Contains: 1) Pulley, 1) 900 082 085 09 - Hex Bolt, 1) 6PK2070 B - Belt for use with AC
+ BSR Class Legal

Crankshaft Pulley Kit (For cars with NO AC)

Crankshaft Pulley Kit (For cars with NO AC) - Sport / Motorsport - Accessory underdrive pulley with multi-rib belt - PORSCHE Boxster / Cayman / 996 / 997 / GT3 Upto-05 | Billet Aluminum Black Anodized - PATRICK MS USA EXCLUSIVE
+ Replaces PN: 996 102 115 63 - Pulley
+ Contains: 1) Pulley, 1) 900 082 085 09 - Hex Bolt, 1) 6PK1890 B - Belt for use without AC
+ BSR Class Legal

Battery Mount for Odyssey PC 925

Battery Carrier Mount - Designed For ODYSSEY PC 925 Batteries - Black Powercoated, Fabricated Steel - Includes Mounting Hardware Kit - PATRICK MS USA

WITH THIS MOUNT YOU CAN LOCATE THE BATTERY WHERE YOU NEED IT TO GET THE BEST WEIGHT DISTRIBUTION AND HOLD THE BATTERY SECURLY FOR ADDED SAFTEY.

Retractable Tow Hook for Porsche 911 & Boxster

RETRACTABLE TOW HOOK, FIT’S 964, 993, 986, 996, BOLT IN FITMENT REPLACING O.E. BUMPER SHOCK, 2)PER CAR, SAFETY RED POWDER COAT FINISH, TIG WELDED CONSTRUCTION & MADE BY PATRICK MOTORSPORTS

SETRAB OIL COOLERS

Patrick Motorsports is a stocking wholesale distributor for Setrab products. Setrab offers a wide variety of cooler types and sizes. Please download the catalog for application information or choose from our exclusively made sizes for Porsche cars. Feel free to contact us for other options.

Momo Steering Wheel Hub Adapter

MOMO STEERING WHEEL ADAPTER HUB FOR PORSCHE BOXSTER 97-04, 944 ALL 85-89, 968 90-94, 911 90-04

SUS 996 343 010 K1

PORSCHE TYPE 996 C2 - BILLET ALUM. MONOBALL FRONT CAMBER PLATE KIT - ALLOWS FOR 1 EXTRA DEG. NEGATIVE CAMBER - INCLUDES HARDWARE

986 996 997 Front Coil Spring Hat Set Bilstein PSS Systems

SPRING PERCH KIT - UPPER FRONT - FOR USE WITH BILSTEIN PSS 9 / PMS 996TT BILLET CAMBER PLATE SET - BILLET ALUM. - BLACK ANO

Swaybar Drop Link Set Front 996 997 GT3

FRONT SWAYBAR DROP LINK SET 996/997, 997 GT3, BOXSTER & CAYMAN

ERS Linear Tender Spring, 2.25 Inch I.D., 150 Lbs, 2.79 Inch Length

ERS Linear Tender Spring - 2.25 Inch I.D. / 150 Lbs. - 2.79 Inch Length - EIBACH

Main Spring - 6 Inch Length - 2.25 Inch I.D. / 350 Lbs

Main Spring - 6 Inch Length - 2.25 Inch I.D. / 350 Lbs. - EIBACH

Main Spring - 6 Inch Length - 2.25 Inch I.D. / 500 Lbs

Main Spring - 6 Inch Length - 2.25 Inch I.D. / 500 Lbs. - EIBACH

Eibach Springs

Eibach Springs - We inventory a wide variety of Eibach products. Main rate springs and progressive tender springs are available in 2.25 and 2.50 inch I.D. in a wide variety of lengths and rates. We also machine and inventory a wide variety of spring hardware for Porsche Coil Over Systems. Please contact us for packages and set up options.

Front Drop Link & Mounts Boxster / Cayman 996 997

Front Extended Drop Link & Mount Set - Longer type links with billet adjustable strut extension mounts. Application: PORSCHE Boxster / Cayman / 996 / 997 / All Models Including Turbo for threaded body dampers. Designed for compatibility to Bilstein PSS9 / Moton / JRZ Systems - TARETT *Please specify suspension system when ordering.

+ Compatible with all suspension systems including Bilstein / JRZ / Ohlins
+ Emulates the GT3 type drop link design. The custom attachment bracket allows for the drop link end to be connected to the strut at a higher location allowing for a longer drop link for improved geometry.
+ Left & right hand threaded rod ends allow for simple length adjustment to eliminate swaybar preload.
+ Used with our PORSCHE Boxster SPEC Racing (BSR) Cars

986 Boxster Bilstein PSS9 Suspension

BILSTEIN PSS9 Suspension System - THE NEW IMPROVED FRONT AND REAR COIL OVER TYPE SUSPENSION PACKAGE FOR PORSCHE 986 Boxster - MSRP: $3233.00

Front and rear coil over shocks with springs. Ride height adjustable. 9 precise compression and rebound settings, from comfort to competition.

Other PN: 48-181440

ALSO USED ON OUR BOXSTER SPEC RACING (BSR) CARS!

Momo Quick Release Steering Wheel Hub

MOMO Quick Release Rally Bolt On/STEERING WHEEL HUB
The new lightweight Quick Releases from MOMO feature a skyway design that saves time when it is crucial. The advanced design allows only one way of installation so that there is no more fumbling of trying to line up a SPLINE design. The MOMO system will also not gall like a SPLINE design does after hard use. This piece need to be welded on the steering column.

ALSO USED IN OUR BOXSTER SPEC RACING (BSR) CARS

Rear Shock Heavy Duty Boxster

SHOCK ABSORBER - HEAVY DUTY - REAR LEFT / RIGHT- PORSCHE BOXSTER/S 986 '97-'04 - (SAME VALVING AS SPORT EDITION W/LONGER SHAFT) - BILSTEIN - LIST: $287.00

Rear Shock Sport Boxster

SHOCK ABSORBER - SPORT - REAR LEFT / RIGHT- PORSCHE BOXSTER/S 986 '97-'04 - BILSTEIN - LIST: $287.00 *SHORTER SHAFT LENGTH IDLE FOR SPORT LOWING SPRINGS

Strut Heavy Duty Front Boxster

STRUT - HEAVY DUTY - FRONT LEFT / RIGHT- PORSCHE BOXSTER / S 986 '97-'04 - SAME VALVING AS SPORT EDITION W/ LONGER SHAFT) - BILSTEIN - LIST: $320.00

Strut Sport Front Boxster

STRUT - SPORT - FRONT LEFT / RIGHT- PORSCHE BOXSTER / S 986 '97-'04 - BILSTEIN - LIST: $320.00 - NOTE: *SHORTER SHAFT LENGTH IDLE FOR SPORT LOWING SPRINGS

Spring Spacer Dividing Collar - Intermediate Inside Locating Ring

Spring Spacer Dividing Collar - Intermediate Inside Locating Ring - For use with 2.25 Inch Springs & M52 x 1.50 threaded body type dampers - Billet Aluminum / Mil-Spec Black Anodized - PATRICK MS USA - Each

TRA 000.044.700.26

SHORT SHIFT KIT – BILLET – PORSCHE 97 ON REDUCES SHIFT BY 35% BOXSTER AND BOXSTER "S" ALL, CAYMAN CAYMAN "S", CARRERA AND CARRERA 4 ALL, CARRERA S" FROM 2005, CARRERA S4 FROM 2006, AND 911 TURBO 2001 THRU 2005 (EXCEPT GT2)

USED ON OUR BOXSTER SPEC RACING (BSR) CARS

TRA 40 309 165

DIFFERENTIAL - QUAIFE ATB - PORSCHE 996 & BOXSTER 986 S - 6-SPEED TRANSMISSIONS

Quaife ATB differential for Porsche 996 6-speed is suitable for Porsche 996 models with 6-speed gearbox, to replace the standard diff only.

Quaife ATB differential for Porsche Boxster S is suitable for Porsche Boxster S models, to replace the standard open differential. A direct replacement for the standard Porsche differential, the Quaife ATB differential transforms your car’s performance.

Shift Rod Linkage Cable End

Shift Rod Linkage Cable End - Billet Adjustable Fastener - Application to all 1997-On Boxster / 996 / 997 models - Direct replacement joint for the weak factory unit - Allows for more precise gear shifts.
+ Replaces OEM plastic shift linkage which has been prone to fail
+ Significantly Reduces Shifter Free Play

ALSO USED ON OUR BOXSTER SPEC RACING (BSR) CARS